DTS Monaco 8.16 Keygen and Patch Download Free

 DTS Monaco is a controller for vehicle diagnosis and general engineering test terminals of the controller functions. The Monaco is derived from the name used for modular Analyzer traffic. In the Mersedec-Bens maintenance tests it is the ultimate authority, perfect support for C4 (SDconnect) and (Ecom) hardware (currently Das-x-entry. Vediamo lower privileges)

 

Free Download DTS Monaco 8.16.015 Keygen and Patch

Resource 1:

https://mega.nz/file/f7IGAKSY#d0ircr6MRFaIo2l2OxEtcvJiIOHsMlfNr2ytSZrYdig

password: wiese@77$12%5

After installing DTS Monaco software, paste Hardware ID to both the Regsitration name and Hardware ID area to generate the activation key

Resource 2:
https://mega.nz/file/300BTBpL#6w2GmO7G7mijkFkbiksN4J9CnlI8FYD9ZEft42CIfTs

 

2 Ways to get license.bin if you want:

1.Directly purchase from Softing.

2. open start > RUN > write : CMD (Command Prompt) and enter

write > ipconfig /all

find > Ethernet adapter Ethernet: then find > Physical Address (example) XX-XX-XX-XX-XX-XX

Send mac address of your LAN adapter to DTS exports (MH, DK forums), they will give you a license file.

 

 

Resource 3:

Get MB SD C4 Xentry, WIS EPC, DTS Monaco, Vediamo software HDD or SSD

https://www.obdii365.com/wholesale/v202006-mb-star-sd-connect-c4-software.html

Send DTS Monaco hardware ID to sales@obdii365.com for the activation key.

If need DTS Monaco 8.14, check here

Free Download and Configure DTS Monaco 8.14 with Openport 2.0

SUPER MB PRO M6 and SD C4 Plus DoIP Which is Better?

 Here is the Mercedes diagnostic multiplexer test report from one of the obdii365.com customers. 

1=SUPER MB PRO M6

2=MB SD C4 Plus DoIP

3=SD Connect Compact C4 old

So I bought a Super MB M6 for fun.

A report from all three.

The first two no longer need batteries or an ad hoc connection.

They have a built-in access point and always show a LAN connection (in SD Toolkit) even though they are connected to WiFi.

The first two can also doip, whether one is needed is an open question.

The first has a built-in fan for better cooling. It works like SD-C4 the configuration must be done in sd toolkit. 

But it makes a very good impression and the workmanship is also good.  It works very well for me.  The connection is stable with the car and computer via wifi (not like in old c4… always on cable). Monaco, vediamo, das, Xentry, update via toolkit everything working. Super MB works with every version, nothing has to be done again. WIS EPC also runs on Win 11. I recommend.

The second has a built-in heatsink at the point where the WLAN card was, which no longer exists.

The first has been in continuous use for several months without any problems.

I tested it today on my S class, the Super MB Pro takes 51.68 sec to communicate and the SD C4 Plus takes 52.09 sec on computer Win 11, I5, 8 GB RAM and SSD.

But the old SD Connect still works.

Conclusion I will only buy the first two in the future, preferably the second, because it has no fan and there is no battery with either.

And here, too, there are only two types, it works or it doesn’t.

This is just information and not a discussion.

Mercedes CRD3 Checksum Bypass Solution by Vediamo

 This is common on Mercedes Benz crd3p.b0, crd3p.e1 and other crd3 ECUs. After writing file with wrong checksum, car start but only once, after you turn ignition off and on it’s continuously off and on 87 kl. relay.

 

To fix this problem you can bypass checksum checking. Follow the method below. All work takes place in the MB SD C4 DoIP Vediamo software.

Free download CRD3_DEV.CBF

1) In vediamo load CRD3_DEV.CBF
establish communication.

2) In function do

FN_SG_Entriegeln_9A

FN_SG_Entriegeln_BC

3) go to variant coding

4) do cpc nicht vorhanden as on the picture

5) reset ecu

How to Set up VXScan ENET Adapter with Xentry Passthru?

 The little VXScan ENET WiFi/USB adapter is tested working with Mercedes Benz Xentry Passthru software on PC.  Here’s the guide to set up ENET adapter for Xentry passthru.

 

This ENET cable can be used with BMW ISTA, VAG ODIS, DTS Monaco programs as well. You can test by your side.

The benefits of ENET adapter with Xentry passthru:

1. For users who got the old none-DoIP MB SD C4/C5 device, you don’t need a brand new DoIP VCI to diagnose DoIP models, just get this cheap dongle as an alternative (for DoIP Mercedes only).

2. If get the dongle, vxscan technician will activate w223 w213 w203 w167 zenzefi license for free

3. If you get yourself Xentry passthru version, vxscan technician will help activate the software

4. It is a versatile adapter. It will also work on iOS, Android phone or tablets. It is compatible with E-SY-S, BimmerCode, Bootmod3, Ethernet, ISTA D, MHD, xHP Flashtool, xDelete, THOR-the M Flasher, BimmerGeeks Pro-Tool, etc. Apps.

5. The dongle is cheap $39.99.

 

How to Set up VXScan ENET Adapter with Xentry Passthru?

Search WiFi name MHD-ENET and pair with password: 123456789

Once connected, run Xentry ENET WiFi Cars (program to switch J2534 devices)

Select passthru interface as DoIP Only

It will launch Xentry software

Run Zenzef-UI program on the desktop

Xentry will ask you to login with user name and password

Contact sales@obdii365.com for user name and password

Select vehicle model, i.e C class W206 and press Xentry Diagnosis

Load ZenZefi license

Software is ready to use

Run a quick test and then perform the functions you desired.

Read also:

How to Activate Benz W223 C206 W213 W167 License to MB SD C4/C6?