10.12.2018

Benz R129 SL500 2001 DME Coding with MB Star HHT-WIN

Model:
Mercedes Benz SL500 (R129) 2001

Problem:
Made a key for a 2001 SL500, car ran fine for 2 days.. Then car won’t start..

Solution:
benz-r129-xprog-1

benz-r129-xprog-2

benz-r129-xprog-3

benz-r129-xprog-4

Took immo box out and read HC05 chip with xprog 5.55, data was garbled..
Tried writing data to two new/used immo boxes.. those were bad too..
julie-emulator-benz-r129-1

julie-emulator-benz-r129-2
Put Julie emulator on DME, a Bosch ME2.0, first try, the car started but no gas pedal, wrote data again and personalized DME, and it worked fine…
When checking DAS authorizations under actual values, make sure to hit the right arrow button, it shows the last authorization…

Procedure to personalize/code DME:
Device used:
MB Star diagnostic scanner SD Connect C4/C5 with software HHT-WIN (latest mb star software has HHT functionality)
mb-star-hht-win-benz-r129-dme-1

Connect C5 Xentry Connect multiplexer via WLAN cable and setup software on my a Dell laptop
Select vehicle model, Control Unit Groups->Drive->ME2-SFI-Motor electronics 2
mb-star-hht-win-benz-r129-dme-2

mb-star-hht-win-benz-r129-dme-3

DAS will automatically selects HHT-WIN
mb-star-hht-win-benz-r129-dme-4

Diagnostic multiplexer is being initialized
Select Actual values->Drive authorization
mb-star-hht-win-benz-r129-dme-5
mb-star-hht-win-benz-r129-dme-6

You can see engine control module  is not compatible nor identified
Engine cannot start either
mb-star-hht-win-benz-r129-dme-7
mb-star-hht-win-benz-r129-dme-8
Start coding
Select Control unit adaptations->Version coding->Read or carry out coding
mb-star-hht-win-benz-r129-dme-9

mb-star-hht-win-benz-r129-dme-10

mb-star-hht-win-benz-r129-dme-11
HHT-WIN displays coding number, coding unit number and chassis,and valid code numbers
mb-star-hht-win-benz-r129-dme-12

mb-star-hht-win-benz-r129-dme-13
Press YES to Transfer coding to new control module
Turn off ignition
mb-star-hht-win-benz-r129-dme-14

Replace old control module with new control module
Turn on ignition
Coding has been carried out
mb-star-hht-win-benz-r129-dme-15

mb-star-hht-win-benz-r129-dme-16
Identification is being carried out.
Engine control module is automatically inerlocked after 40 engine starts
mb-star-hht-win-benz-r129-dme-17

Engine starts
engine speed raise from o to 1250 rpm or so and the green indicators on MB SD C5 unit flash
mb-star-hht-win-benz-r129-dme-18

mb-star-hht-win-benz-r129-dme-19

Initiate interlocking
mb-star-hht-win-benz-r129-dme-20
mb-star-hht-win-benz-r129-dme-21

The control module is interlocked and permanently assigned to the vehicle
Switch off ignition
Turn on ignition
Now go back to check actual values
mb-star-hht-win-benz-r129-dme-22

mb-star-hht-win-benz-r129-dme-23
mb-star-hht-win-benz-r129-dme-24

Engine module is identified/interlocked and engine is able to start.
Done.

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.